Deskripsi
To reduce the effect of these load disturbances, sensors and transmitters collect information about the process variable and its relationship to some desired set point. A controller then processes this information and decides what must be done to get the process variable back to where it should be after a load disturbance occurs.
When all the measuring, comparing, and calculating are done, some type of final control element must implement the strategy selected by the controller.
The most common final control element in the process control industries is the control valve. The control valve manipulates a flowing fluid, such as gas, steam, water, or chemical compounds, to compensate for the load disturbance and keep the regulated process variable as close as possible to the desired set point.
Many people who talk about control valves or valves are really referring to a control valve assembly. The control valve assembly typically consists of the valve body, the internal trim parts, an actuator to provide the motive power to operate the valve, and a variety of additional valve accessories, which can include positioners, transducers, supply pressure regulators, manual operators, snubbers, or limit switches.
Whether it is called a valve, control valve or a control valve assembly is not as important as recognizing that the control valve is a critical part of the control loop. It is not accurate to say that the control valve is the most important part of the loop. It is useful to think of a control loop as an instrumentation chain. Like any other chain, the whole chain is only as good as its weakest link. It is important to ensure that the control valve is not the weakest link.
Training control valve: operation maintenance troubleshooting ini memerlukan pendalaman materi yang komprehensif dan terupdate, oleh karenanya dibutuhkan training provider yang dapat menyediakan training control valve sesuai dengan kebutuhan peserta.
Tujuan Pelatihan
Dengan mengikuti training maintenance control valve, maka diharapkan :
- To able know to introduction to control valves
- To able know to control valve performance
- To able know to valve and actuator types
- To able know to control valve accessories
- To able know to control valve selection
- To able know to special control valves
- To able know to installation and maintenance
Outline Materi
Modul pelatihan secara umum adalah sebagai berikut.
- Introduction to Control Valves: What Is A Control Valve?, Process Control Terminology, Sliding-Stem Control Valve Terminology, Rotary-Shaft Control Valve Terminology, Control Valve Functions and Characteristics Terminology.
- Control Valve Performance: Dead Band, Actuator-Positioner Design, Valve Response Time, Valve Type And Characterization, Valve Sizing.
- Valve and Actuator Types: Control Valves, Control Valve End Connections, Valve Body Bonnets, Control Valve Packing, Characterization of Cage-Guided Valve Bodies, Valve Plug Guiding, Restricted-Capacity Control Valve Trim, Actuators.
- Control Valve Accessories: Positioners, Other Control Valve Accessories
- Control Valve Selection: Valve Body Material, Designations for the High Nickel alloys, Pressure-Temperature Ratings for Standard Class, Face-to-Face Dimensions, Control Valve Seat Leakage Classifications, Control Valve Flow Characteristics, Valve Sizing, Non-Destructive Test Procedures, Cavitation and Flashing
- Special Control Valves: High Capacity Control Valves, Low Flow Control Valves, High-Temperature Control Valves, Cryogenic Service Valves, Customized Characteristics and Noise Abatement Trims, Valves Subject to Sulfide Stress Cracking
- Installation and Maintenance: Proper Storage and Protection, Proper Installation Techniques, Control Valve Maintenance, Actuator Diaphragm, Stem Packing, Seat Rings, Bench Set.
Instruktur :
Instruktur yang akan mengajar pelatihan control valve ini berasal dari praktisi yang sudah berpengalaman di bidangnya, dan atau akademisi yang berpengalaman menjadi konsultan di banyak perusahaan besar.
Metode Training :
Pelatihan maintenance control valve ini dapat diselenggarakan dengan cara tatap muka / offline maupun online / daring
Lokasi :
Beberapa kota tempat pelatihan opeation control valve antara lain : Jakarta, Yogyakarta, Bandung dan Bali
Jadwal pelatihan training-industrisipil.com 2026 :
Batch 1 : 03 – 04 Januari 2026 | 16 – 17 Januari 2026 || Batch 2 : 06 – 07 Februari 2026 | 20 – 21 Februari 2026 || Batch 3 : 05 – 06 Maret 2026 | 19 – 20 Maret 2026
Batch 4 : 03 – 04 April 2026 | 23 – 24 April 2026 || Batch 5 : 07 – 08 Mei 2026 | 21 – 22 Mei 2026 || Batch 6 : 05 – 06 Juni 2026 | 25 – 26 Juni 2026
Batch 7 : 09 – 10 Juli 2026 | 23 – 24 Juli 2026 || Batch 8 : 06 – 07 Agustus 2026 | 20 – 21 Agustus 2026 || Batch 9 : 04 – 05 September 2026 | 18 – 19 September 2026
Batch 10 : 08 – 09 Oktober 2026 | 22 – 23 Oktober 2026 || Batch 11 : 06 – 07 November 2026 | 26 – 27 November 2026 || Batch 12 : 04 – 05 Desember 2026 | 18 – 19 Desember 2026
Catatan : Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta training
Invetasi dan Lokasi pelatihan
· Yogyakarta, Hotel 101 (6.500.000 IDR / participant)
· Jakarta, Hotel Amaris Kemang (6.500.000 IDR / participant)
· Bandung, Hotel Neo Dipatiukur (6.500.000 IDR / participant)
· Bali, Hotel Ibis Kuta(7.500.000 IDR / participant)
· Surabaya, Hotel Amaris, Ibis Style (6.000.000 IDR / participant)
· Lombok, Sentosa Resort (7.500.000 IDR / participant)
Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.
Fasilitas :
FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
FREE Akomodasi ke tempat pelatihan bagi peserta training
Module / Handout training
FREE Flashdisk
Sertifikat training
FREE Bag or bagpackers (Tas Training)
Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
2xCoffe Break & 1 Lunch, Dinner
FREE Souvenir Exclusive
Training room full AC and Multimedia
